Don't have an account? Create one!
Lift handle Housing
Part Number: LY-2277
$4.07 each
- In-Stock.Ships via UPS/Fedex
Replacement lift handle housing for Lyon lockers.
Material: chrome plated Zamak
Thickness: varies, from 1/16" to 1/8"
Lift - broke down into the following sections:
Upper 'grip' section
Lower section with padlock hole
Lockbar fingers
Height
Of upper and lower sections combined at front of handle: 2-1/2"
At back of handle: 3-3/16"
Upper grip portion
Front: 1-3/16"
Back: 1-5/8"
Lower padlock portion
Front: 1-5/16"
Back: 1-1/32"
Depth grip portion
Not including lockbar fingers: 11/16"
Including lockbar fingers: 1-3/8"
Padlock portion
Not including lockbar fingers: 11/16"
Including lockbar fingers: 1-9/32"
Lockbar fingers - come out from the handle portion, then take a 90 degree bend to the left - this portion is where you identify the handing. The bent portion fits into the lockbar. In addition, at the base of each finger are platforms that lay between, and perpendicular to the handle portion and mounting fingers. These platforms butt up against the outside of the door when the handle is in place, acting like a stop.
Length from handle to bend, including platforms: 11/16"
Length from bend to tip that goes in lockbar: 9/16"
Height - there are three -
Between the handle and 90 degree bend: /16"
The 90 degree bend portion - the first half, closest to the bend, extends down past the half by the tip. This extra material acts as a stop for the fingers, and it butts up against the lockbar when the fingers are in place.
Height of first half: 1/2"
Height of second half, at tip: 19/64"(between 9/32" and 5/16")
Center of top finger to center of bottom finger: 11/16"
Padlock hole
Dia: 3/8"
Housing
Front of base
Height
At the back: 4-1/6"
At the front: 3-3/4"
Width
At the back: 1-1/32"
At the front top and bottom portions: 3/4"
By the lift slot hole: 19/32"
Mounting at the top - on the back of base, at the top, there is a mounting tab. It comes horizontally out of the back of the base and then takes a 90 degree bend up. This tab fits into a slot in the locker door and holds the top of the base in place.
Width: 7/16"
Length from back of base to bend: 3/16"
Height
From bend to tip: 7/32"
At the bottom - there is a mounting hole, accessible only from the back
Dia: 5/32"
Center of hole to center of horizontal portion of upper tab: 3-5/16"
Lift slot
Height: 1-3/16"
Width: 7/16"
Kick-proof hood
Width
At base: 7/16"
At front: 3/8"
Height
At base: 1-27/32"
At front: 1-5/16"
Padlock hole dia: 13/32"
Mounting hardware (needed for housing only)
1 each LY 8-32 x 1/4" Hex head machine screw
Thickness: varies, from 1/16" to 1/8"
Lift - broke down into the following sections:
Upper 'grip' section
Lower section with padlock hole
Lockbar fingers
Height
Of upper and lower sections combined at front of handle: 2-1/2"
At back of handle: 3-3/16"
Upper grip portion
Front: 1-3/16"
Back: 1-5/8"
Lower padlock portion
Front: 1-5/16"
Back: 1-1/32"
Depth grip portion
Not including lockbar fingers: 11/16"
Including lockbar fingers: 1-3/8"
Padlock portion
Not including lockbar fingers: 11/16"
Including lockbar fingers: 1-9/32"
Lockbar fingers - come out from the handle portion, then take a 90 degree bend to the left - this portion is where you identify the handing. The bent portion fits into the lockbar. In addition, at the base of each finger are platforms that lay between, and perpendicular to the handle portion and mounting fingers. These platforms butt up against the outside of the door when the handle is in place, acting like a stop.
Length from handle to bend, including platforms: 11/16"
Length from bend to tip that goes in lockbar: 9/16"
Height - there are three -
Between the handle and 90 degree bend: /16"
The 90 degree bend portion - the first half, closest to the bend, extends down past the half by the tip. This extra material acts as a stop for the fingers, and it butts up against the lockbar when the fingers are in place.
Height of first half: 1/2"
Height of second half, at tip: 19/64"(between 9/32" and 5/16")
Center of top finger to center of bottom finger: 11/16"
Padlock hole
Dia: 3/8"
Housing
Front of base
Height
At the back: 4-1/6"
At the front: 3-3/4"
Width
At the back: 1-1/32"
At the front top and bottom portions: 3/4"
By the lift slot hole: 19/32"
Mounting at the top - on the back of base, at the top, there is a mounting tab. It comes horizontally out of the back of the base and then takes a 90 degree bend up. This tab fits into a slot in the locker door and holds the top of the base in place.
Width: 7/16"
Length from back of base to bend: 3/16"
Height
From bend to tip: 7/32"
At the bottom - there is a mounting hole, accessible only from the back
Dia: 5/32"
Center of hole to center of horizontal portion of upper tab: 3-5/16"
Lift slot
Height: 1-3/16"
Width: 7/16"
Kick-proof hood
Width
At base: 7/16"
At front: 3/8"
Height
At base: 1-27/32"
At front: 1-5/16"
Padlock hole dia: 13/32"
Mounting hardware (needed for housing only)
1 each LY 8-32 x 1/4" Hex head machine screw
Lift, Right Hand, For Locker Handle LY-2232-RH, Post 1981
Part Number: LY-2278-RH
$4.33 each
see more products in:
Lyon